Description
xUPR Signature Series Billet Catch Can System with Rear (Master Cylinder) Mounting Bracket for your 2012 to 2018 JEEP Wrangler. This Catch Can kit was developed to allow room for accessories like Power Distribution modules and some on-board air compressors, and to out perform all the other 2 chamber catch cans with a patented internal diffuser system that forces the oil to be released into the catch can from a lower chamber then the fresh air can exit through the upper chamber. This is because all the traditional 2 chamber catch cans have two chambers side by side and with a screen that separates them. Side by Side chambers with a simple screen or honeycomb filter allow oil to be sucked right across and out the exit port of the catch can.
Most of the top brands out there are what is called 2 chamber pull through catch cans as they all allow as much oil to be pulled through them as they collect and this is why they can have such small oil capacities and be drained so infrequently. With the UPR Catch Can you have to check them every 500 miles to maintain the oil level. Whereas other catch cans usually say to check them every 2000 to 3000 miles and you should be fine. UPR takes pride in their products and always strives to deliver the best looking and performing products.
All UPR Catch Cans are machined from 6061 Billet Aluminum and use forged aluminum fittings along with Viton O-rings and the highest quality Braided Hoses on every model. We don't sell you a catch can and with all the rubber or plastic hoses and plastic fittings and then tell you to get the best you have to upgrade your hose and fittings. With UPR it all comes STANDARD at no extra cost!
This setup was designed for all the JEEP enthusiasts to eliminate the dreaded Blue Smoke Screen when off roading or rock crawling.
You will see improved MPG and Improved Performance throughout the Entire RPM range.
The UPR Oil Catch Can features a three chamber design CNC machined from 6061 Billet Aluminum unlike some of our competitors models that are single chamber tanks that don't properly trap the oil or debris.
Installs in 20-30 minutes or less.
This UPR Pro Series catch can kit is shipped ready to install even if no upgrades are selected. Upgrades are available to allow you to tailor the kit to fit your needs.
Optional Parts:
UPR Billet One-Way Valve Cover Breather:
These are Valve Cover Breathers with a one-way valve inside of it. These are designed to allow excess/positive crankcase pressure to exit through the breather when in boost. Then it closes to return to vacuum while driving to prevent un-metered air from entering to maintain perfect drivability. These are also ideal for vehicles in very cold or freezing weather as it allows crankcase pressure to escape until condensation or frozen condensation in the PCV hoses melts or thaws. This is a must to ensure maximum engine seal life.
SS Magnetic Drain Plug:
The Stainless Steel magnetic drain plug would replace the drain plug on the bottom of the catch can with an allen head plug that has a magnet embedded into it. It will attract any ferrous metal material to it so the user can inspect it. If you select this option you can not also use the Drain Line kit below.
Replacement O-Rings:
Spare O-rings for the catch can cup. If the O-ring is lost, torn or if it's just time to replace it due to wear it's a good idea to have a couple of spares in the glove box.
Optional Parts:
UPR Billet One-Way Valve Cover Breather:
These are Valve Cover Breathers with a one-way valve inside of it. These are designed to allow excess/positive crankcase pressure to exit through the breather when in boost. Then it closes to return to vacuum while driving to prevent un-metered air from entering to maintain perfect drivability. These are also ideal for vehicles in very cold or freezing weather as it allows crankcase pressure to escape until condensation or frozen condensation in the PCV hoses melts or thaws. This is a must to ensure maximum engine seal life.
SS Magnetic Drain Plug:
The Stainless Steel magnetic drain plug would replace the drain plug on the bottom of the catch can with an allen head plug that has a magnet embedded into it. It will attract any ferrous metal material to it so the user can inspect it. If you select this option you can not also use the Drain Line kit below.
Replacement O-Rings:
Spare O-rings for the catch can cup. If the O-ring is lost, torn or if it's just time to replace it due to wear it's a good idea to have a couple of spares in the glove box.
THIS PART DOES NOT CARRY AN CARB EO NUMBER, AND THEREFORE IS FOR RACING / OFF ROAD USE ONLY. NOT FOR SALE OR USE IN CALIFORNIA DUE TO CARB/EMISSIONS. ALL CALIFORNIA ORDERS WILL BE CANCELLED AND REFUNDED
Product Features:
» Show Quality Finish
» 5/8" Black Billet 90* fittings
» Can measures 4.50" x 2.5"
» Super Easy 20-30 minute install
» 5/8" Oil Resistant Hose included
» Billet Mounting Bracket System
» Improves Fuel Economy & Performance
» High Quality CNC Machined Billet Aluminum
» Multi-Stage Patented Diffuser Prevents Oil from Entering Intake
» Available in Satin Silver, Black, Blue or Red - Select Finish Above
Fits These Vehicles:
2012 2013 2014 2015 2016 2017 2018 Jeep Wrangler JK 3.6
Made in the USA!
Vehicle Fitment
x- Choosing a selection results in a full page refresh.